Donor M20 Procured

On Saturday I borrowed an engine hoist from local e30 maven Eric Berger, put it in a rental truck and drove up to Walnut Creek to pull a donor M20 for my car. Though Bernz (owner of the donor motor) and her neighbor Dillan are pretty experienced with motor removal it took 5 hours, lots of spilled engine fluids and a few mistakes to get it out of the car.

The donor motor has 75,382 miles on it and I’m looking forward to putting another 150,000 miles on it myself. The motor will get a complete inspection, all the wear and tear parts will be replaced (except the head gasket) and then it will be installed in my car. My car will probably be off the road for 2 weeks to facilitate the swap and maintenance.

IMG_7057

AFM and airbox removed.

IMG_7065

Finally removing the engine.

IMG_7067

Engine almost removed.

IMG_7073

Dillan removing automatic transmission.

IMG_7083

Strapped in for the trip back to home.

M20 Motor Removal Checklist


  • 2x Heater inlet/outlet hoses at the firewall. Flat head screwdriver for the clamps.
  • 2x fuel lines, the feed and return, 1 at either end of the fuel rail. Flat head screwdriver for the clamps.
  • 2x engine mounts, 1 each side. 16mm / 17mm bolt.
  • Engine ground to oil pan. 13mm bolt.
  • Radiator. 2x 10mm bolts holding the top support bracket.
  • Radiator hoses to radiator. Just more flat headed clamps.
  • Brake booster hoses. Flat headed screws.
  • Exhaust down pipes. 17mm 16mm bolts. You can drop and remove the exhaust if you like, but you have got room in some cases.
  • Intake boot, air box. More flat head screws, 10mm bolts for the air box.
  • Driveshaft, 3x 17mm bolts with 17mm nuts.
  • Shifter linkage. 13mm bolts various sizes in places.
  • Wiring loom, just unplug from the ECU and toss it over the engine, unbolt the harness ground to chassis, usually somewhere by the strut tower.
  • Power cable to the Starter motor. Just disconnect from the back of the starter motor and leave it in the car.
  • Remove gearbox X-member. 13mm bolts.

M20 Motor Removal Walkthrough


  1. Let the car run in the park position if you have an automatic or let it run in the N position if you have 5 speed while you pull fuse 11 to empty all fuel from the system. Make sure you have your E brake on if you have a 5 speed. When the car shuts off turn your key to the off position.
  2. Go to your trunk and unhook your battery. You will need a 13mm wrench. Unhook the (-) side of the battery first then continue to the (+) side.
  3. Once they are unhooked pull them off and push them to the side. This is what you should have.
  4. Then go to your glove box to unhook your ECU.
  5. Open it up and here is the ECU plug. You will want to pull this silver clip back and unhook the ECU.
  6. Now go out to the engine bay and unhook all of the power wires from the distribution block on the firewall. You will need a 10mm wrench.
  7. Then unhook the ground wire from the strut tower. Also a 10mm.
  8. Now pull the plug for the ECU through the firewall.
  9. Next you can unhook the coil. pull the plug wire and boot off the top and you will see two wires. You will need a 8mm socket and a 10mm socket.
  10. Now go to the driver side of the car and unhook the MAF.
  11. Then take a flat head screw driver and loosen the clamp that holds the boot onto the MAF and take it out. You will need a 10mm wrench to loosen the two bolts on the side of the air box.
  12. Now its time to unhook the rad. You will need a bucket to catch your coolant. We have a drian in our floor that goes to a holding tank so we didnt need one.
  13. First take the hose off the bottom of the rad on the driver side. you will need a flat head screwdriver.
  14. Then unhook the hose on the passenger side.
  15. While your over there unhook the coolant sensor on the side of the rad.
  16. Now unhook the top hose.
  17. Now its time to take the radiator bracket off. You will need a 10mm wrench.
  18. Now pull your radiator out and put it to the side so you wont poke any holes in it.
  19. Now go back over to the driver side and unhook your throttle cable. You will need a 10mm.
  20. Then pull the throttle back and unhook your cable and pull it out.
  21. Now its time to unhook the c101 plug. This is located next to the fuse box and it just untwist.
  22. Now you can get down in and unhook your hoses for your heater core. You will need a flat head for this also.
  23. Now you can unhook the vac hoses from the brake booster to the TB. These just slide out with a little wiggle.
  24. Now its time to unhook your fuel lines. First one up is the one on the FPR. Be careful when you do this so it doesnt get in your eyes.
  25. Now do the one on the fuel rail, be very carful on this on since it will have more pressure in it then the first one.
  26. Now unhook your plug and hose from your evap can. This is located under the throttle body.
  27. Now unhook the ground straps from the oil pan to the frame. You will need a 13mm for this.
  28. It may help to jack up the front end of the car slighly higher to make removing the engine easier.
  29. Leave a Comment

    You must be logged in to post a comment.

    Tags: , , , , , ,

    April 8, 2013 mechanical, status